Error Code P0532 is defined as A/C Refrigerant Pressure Sensor A Circuit Low Input, meaning there’s an abnormally low voltage reading coming from the A/C refrigerant pressure sensor circuit, which could be caused by too little or too much refrigerant in the system.

This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made since 1996 up to present. It is particularly prevalent among Romeo, Chevrolet, Dodge, Ford, Hyundai, Honda, Vauxhall, Volvo, etc. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model to another.

The A/C (air conditioning) refrigerant pressure sensor helps the HVAC (Heating, Ventilation, and Air Conditioning) system in regulating the temperature inside the vehicle according to passenger’s settings/demands. This system is connected to two other systems, namely the BCM (Body Control Module) and the ECC (Electronic Climate Control) module, which both monitors the sensors and determines system pressure, which in turn can engage/disengage the compressor accordingly.

The A/C refrigerant pressure sensor works as a pressure transducer, which converts refrigerant system pressure to analog electrical signal, which allows monitoring through the vehicle’s modules. This works by using three wires: a 5-volt reference wire, signal wire, and a ground wire. The modules compare the signal wire’s values to the 5-volt reference, and can instantly calculate system pressures with this info.

Error Code P0532 takes place when the module determines a low electrical value within the A/C refrigerant pressure sensor A or its circuit.

Other related error codes include:

  • Error Code P0530
  • Error Code P0531
  • Error Code P0533

Common Symptoms

As with other error codes, this code activates the Check Engine light and registers the code to the vehicle’s memory system. The A/C light may flash repeatedly. Other symptoms include:

  • Inaccurate temperature from the fan air
  • Erratic or fluctuating fan air temperature
  • Limited use of HVAC
  • Abnormal operation on the HVAC system
  • A/C compressor is not engaging when needed

Possible Causes

Common causes for this code include:

  • Damaged or defective A/C refrigerant pressure sensor
  • Leaking A/C refrigerant pressure sensor
  • Low or incorrect refrigerant pressure or level
  • Too little or too much refrigerant in the A/C system
  • Open or short in the A/C refrigerant pressure sensor circuit
  • Damaged or defective electrical connectors
  • Defective climate control head
  • Issues in the ECC (Electronic Climate Control) or BCM (Body Control Module)

How to Check

Like many codes, it is best to research this code on the TSB (technical service bulletin) for the specific year, model, and transmission.

To start the diagnosis, you have to check the A/C refrigerant pressure sensor’s operation. Your diagnosis of this code depends on the tools and knowledge you have. Monitor the pressure and other related values while the system is running, and verify the functionality of the sensors using your OBD reader/scan tool.

Note: If you have no prior experience of working with refrigerant, it is highly recommended that you ask the help of a certified professional, as this component can be a safety hazard.

Then, test the A/C refrigerant pressure sensor. This will usually have three wires; test between the pins and record your results. The desired value for this test dramatically varies between manufacturers, type of sensor, temperature, etc., so make sure your information is accurate.

Note: When testing pins/connectors, make sure you use the right test pins and multimeter. Damaged pins or connectors could cause future intermittent hard-to-find electrical gremlins.

Lastly, check the wiring. In many cases, these sensors are mounted on an A/C pressure line, or close to the line connection, this is to make sure the harness is routed correctly.

Also in many cases, the sensors can be damaged by moving parts under the hood, which happens when the lines are not secured correctly. Also, make sure the sensor looks good, and its lines are adequately fastened.

How to Fix

Depending on the diagnosis, common repairs include:

  • Checking the refrigerant level, and adding only if necessary
  • Repair or replacement of the cooling fans
  • Replacement of the defective A/C refrigerant pressure sensor
  • Repair or replacement of open, shorted, burnt, and corroded, wires and connectors

Since this code could mean a refrigerant leak, then it should be addressed as soon as possible, since a leaking refrigerant is a safety issue. Also, when attempting to diagnose or repair the A/C system, make sure you know basic refrigerant safety.